Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and safety measures
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and the other fixed glasses
   Removal and installation of an overlay and bearing beam of bumpers
   Removal and installation of a decorative lattice of a radiator (model since 03.1997 вып.)
   Removal and installation локера a wheel arch
   Removal and panel installation обтекателя a windscreen
   Removal and cowl installation
   Replacement of loops of a cowl
   Removal and installation of a forward wing
   Replacement of an overlay of a back wheel arch (model Corsa and Combo)
   Removal and installation of facing of doors
   Removal and installation of glass of a forward door
   Removal and installation of glass of a back door (model Corsa)
   Removal and installation стеклоподъемника
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock of a forward door
   Removal and installation of the lock of a door
   Protection against freezing of locks and consolidations
   Removal and installation of an external mirror and the e/motor of its drive
   Removal and installation of the case of an external mirror
   Removal, installation and door adjustment
   Removal and installation of a door of a back (model Corsa and Tigra)
   Removal and installation of the lock of a door of a back (model Corsa and Tigra)
   Removal, installation, dismantling and assemblage of the external handle and the cylinder of the lock of a door of a back (model Corsa)
   Натяжитель a seat belt
   Security measures at the reference with emergency преднатяжителем a seat belt and a lateral pillow of safety
   Removal and installation of a forward seat
   Removal and installation of a back seat
   Removal and installation of the central console
   Removal and installation of lateral facing of a foot well of the forward passenger
   Removal and installation of a ware box
   Removal and installation of an internal mirror and installation of a plate of its fastening
   Removal and installation of the panel of devices
   The sdvizhnaja panel of a roof
+ Onboard electric equipment


Removal and installation of an overlay and bearing beam of bumpers

Forward bumper

Models till 02.1997 of release

 PERFORMANCE ORDER

  1. Turn out two bolts (1) about an air inlet.

Bolts of fastening of an overlay of a forward bumper

  1. Turn out from below three bolts (2) of a face-to-face beam of a body.
  2. Turn out four bolts (3) of локеров wheel arches.
  3. Give two nuts (4) from overlays of a wheel arch.
  4. On the cars equipped with washers of lenses of headlights, disconnect hoses from snuffled.
  5. On the cars equipped with antifog headlights, separate their sockets.
  6. Take away overlays of wheel arches from wings and, by means of the assistant, remove an overlay of a forward bumper.
  7. Disconnect from a bearing beam a cable (1) and turn out bolts of its fastening (2) On model Tigra preliminary disconnect from a bearing beam shock-absorbers of a forward bumper.

Fastening of a cable (1) and a bearing beam (2)

  1. Establish acting in film components in an order, the return to a removal order.
  2. If establish washers of lenses of headlights on models Corsa and Combo, drill adjusting apertures according to the sizes resulted on an accompanying illustration. Establish nozzles and connect to them hoses.

The adjusting sizes of a washer of lenses of headlights

  1. Join штекерное connection of an antifog headlight if it is available, fix the tip.

Models since 03.1997 of release

The overlay of a forward bumper and decorative lattice of a radiator act in film separately.

Bolts of fastening of an overlay of a forward bumper

Back bumper (Models Corsa and Tigra)

 PERFORMANCE ORDER

  1. Remove a lamp of illumination of licence plate (the Onboard electric equipment see the Head).
  2. Remove an overlay of a back bumper. For this purpose give the fixture listed on an accompanying illustration. On models Tigra there are no screws (1), but two screws over licence plate are added.

Elements of fastening of an overlay of a back bumper of model Corsa
1, 2 — Screws
3 — Plastic nuts

  1. Wring out an overlay of a wheel arch and remove.
  2. If necessary turn out bolts of fastening and remove bearing beam of a back bumper On model Tigra preliminary remove the shock-absorber of a bearing beam.

Fixture of a bearing beam of a back bumper