Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and safety measures
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and the other fixed glasses
   Removal and installation of an overlay and bearing beam of bumpers
   Removal and installation of a decorative lattice of a radiator (model since 03.1997 вып.)
   Removal and installation локера a wheel arch
   Removal and panel installation обтекателя a windscreen
   Removal and cowl installation
   Replacement of loops of a cowl
   Removal and installation of a forward wing
   Replacement of an overlay of a back wheel arch (model Corsa and Combo)
   Removal and installation of facing of doors
   Removal and installation of glass of a forward door
   Removal and installation of glass of a back door (model Corsa)
   Removal and installation стеклоподъемника
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock of a forward door
   Removal and installation of the lock of a door
   Protection against freezing of locks and consolidations
   Removal and installation of an external mirror and the e/motor of its drive
   Removal and installation of the case of an external mirror
   Removal, installation and door adjustment
   Removal and installation of a door of a back (model Corsa and Tigra)
   Removal and installation of the lock of a door of a back (model Corsa and Tigra)
   Removal, installation, dismantling and assemblage of the external handle and the cylinder of the lock of a door of a back (model Corsa)
   Натяжитель a seat belt
   Security measures at the reference with emergency преднатяжителем a seat belt and a lateral pillow of safety
   Removal and installation of a forward seat
   Removal and installation of a back seat
   Removal and installation of the central console
   Removal and installation of lateral facing of a foot well of the forward passenger
   Removal and installation of a ware box
   Removal and installation of an internal mirror and installation of a plate of its fastening
   Removal and installation of the panel of devices
   The sdvizhnaja panel of a roof
+ Onboard electric equipment


Removal and installation of an internal mirror and installation of a plate of its fastening

Removal and installation

 PERFORMANCE ORDER

  1. Remove the mirror basis upwards from a plate for its fastening.

Do not separate a mirror from its spherical head. If it has occurred, remove the basis and put a mirror in the turned position on a flat surface. Grease a spherical head with greasing and press by means of wooden бруска in spherical подпятник mirrors.

  1. Insert a mirror against the stop into a plate of its fastening.

Installation of a plate of fastening of a mirror

 PERFORMANCE ORDER

  1. Clear glass around installation by a cleaner for grids, for example, OPEL 1759201.
  2. Limit area of installation to a sticky tape according to an accompanying illustration.

Restriction of area of installation of a plate of fastening of a mirror
A— 50 mm
B— The glass Center

  1. Smooth out a pasted surface of a plate an emery paper of granularity Р100 and clear.
  2. Mix two-componental glue, for example, OPEL 1504803 (90295281) and put its layer in the thickness about 1 mm on a plate.

Gluing condition is the ambient temperature about +20 hailstones.

  1. Put a plate to glass and fix its sticky tape.
  2. Through 80 mines glue stiffens and on a plate it is possible to establish a mirror.

By heating of a place of pasting by the hair dryer time of hardening of glue can be reduced. The temperature of heating of a place of pasting should not exceed +80 hailstones.