Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and safety measures
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and the other fixed glasses
   Removal and installation of an overlay and bearing beam of bumpers
   Removal and installation of a decorative lattice of a radiator (model since 03.1997 вып.)
   Removal and installation локера a wheel arch
   Removal and panel installation обтекателя a windscreen
   Removal and cowl installation
   Replacement of loops of a cowl
   Removal and installation of a forward wing
   Replacement of an overlay of a back wheel arch (model Corsa and Combo)
   Removal and installation of facing of doors
   Removal and installation of glass of a forward door
   Removal and installation of glass of a back door (model Corsa)
   Removal and installation стеклоподъемника
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock of a forward door
   Removal and installation of the lock of a door
   Protection against freezing of locks and consolidations
   Removal and installation of an external mirror and the e/motor of its drive
   Removal and installation of the case of an external mirror
   Removal, installation and door adjustment
   Removal and installation of a door of a back (model Corsa and Tigra)
   Removal and installation of the lock of a door of a back (model Corsa and Tigra)
   Removal, installation, dismantling and assemblage of the external handle and the cylinder of the lock of a door of a back (model Corsa)
   Натяжитель a seat belt
   Security measures at the reference with emergency преднатяжителем a seat belt and a lateral pillow of safety
   Removal and installation of a forward seat
   Removal and installation of a back seat
   Removal and installation of the central console
   Removal and installation of lateral facing of a foot well of the forward passenger
   Removal and installation of a ware box
   Removal and installation of an internal mirror and installation of a plate of its fastening
   Removal and installation of the panel of devices
   The sdvizhnaja panel of a roof
+ Onboard electric equipment


Removal and installation of a forward wing

Removal

 PERFORMANCE ORDER

  1. Remove an overlay of a forward bumper (see Has undressed Removal and installation of an overlay and a bearing beam of bumpers).
  2. Beat out the core of a rivet (1) by means of a screw-driver and remove a rivet with локера a wheel arch.

Fixture of a forward wing

  1. Remove the lateral index of turn (the Onboard electric equipment see the Head).
  2. Fix a cowl in completely open position by a persistent bar. A cowl and loops protect from damage of their paint and varnish covering.
  3. Turn out bolts (2) of a wing, bolts (3) of rack A, and also bolts (4).
  4. Remove a wing from a body. Thus cut off a sharp knife hermetic or heat up its hair dryer.

Installation

 PERFORMANCE ORDER

  1. At aerial installation on the left wing of models Combo drill an aperture according to the resulted scheme. Smooth out aperture edges, ground and paint over them.

Drilling marking under the aerial

  1. Smooth out a basic element of a wing on a body and condense with its tape OPEL 90 350 106 (15 05 301) or any other sealing tape.

Consolidation of a basic element of a wing

  1. Establish a wing and tighten bolts of its fastening. The distance between a cowl and a wing, and also distance from a back edge of a wing to a forward door should make 4 1 mm. Watch position of a wing concerning a headlight. The wing should act over a plane of a forward door on 0 2 mm.
  2. Put a protective wax covering on a wing inside.
  3. Fix локер a wheel arch.
  4. Establish the lateral index of turn (the Onboard electric equipment see the Head).
  5. Establish an overlay of a forward bumper.