Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
- Systems of an electric equipment of the engine
   The general information and safety measures
   + Electronic control system of ignition (and injection) petrol engines
   + Systems of preheat and heating of fuel of the diesel engine
   + Charge and start systems
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Systems of an electric equipment of the engine

Ignition system (petrol models)

Type

Engines X10XE, X12XE Electronic with direct Ignition (EST)
Engines X12SZ, X14SZ, C14SE, X14XE, X16XE, C16XE Electronic with direct ignition (DIS)
Engine C14NZ Electronic with the gauge of the Hall and The distributor (EZF-h)

Ignition order (the first cylinder is located from outside drive ГРМ)

Engines, except X10XE
1-3-4-2
Engines H10HE
1-2-3

The ignition coil

Resistance of a primary winding, Ohm
0.45
Resistance of a secondary winding, clod
5 7

Preheat system (diesel models)

Type of candles накаливания

The engine of 1.7 l SOHC
Champion CH 163
The engine of 1.7 l DOHC
The information is absent
Engines of 2.0 l
Champion CH 207

Resistance of candles накаливания, the Ohm

0.4

Control system of the engine

Codes of malfunctions OBD I

The control lamp of refusals (MIL) lights up in case of occurrence of malfunctions in system.


Code designation

Possible source of infringement

12
Inclusion of a mode of delivery of codes
13
Absence of change of pressure on a ljambda-probe
14
The underestimated pressure on gauge ECT
15
The overestimated pressure on gauge ECT
16
Incorrect signal from the detonation gauge (KS)
17
Absence of impulses on injection injectors
18
See 16
19
The gauge of turns of the engine is faulty
21
The overestimated pressure on the gauge of position throttle заслонки (TPS)
22
The underestimated pressure on gauge TPS
24
The gauge of speed (VSS) is faulty
25
The overestimated/underestimated pressure on injector TBI/MFI
28
Absence of contact of the relay of the fuel pump
29
The underestimated pressure of the relay of the fuel pump
32
The overestimated pressure of the relay of the fuel pump
33
The overestimated pressure on gauge MAP
34
The underestimated pressure on gauge MAP
35
Gauge IAC is faulty
41
The overestimated pressure on the ignition module (DIS)
42
The overestimated pressure on the electronic block of management of ignition
43
System EGR is faulty
44
The reimpoverished air-fuel mix
45
The reenriched air-fuel mix
46
Incorrect target pressure of the amplifier
47
The gauge of position of the valve of system EGR is faulty
49
The overestimated pressure of the battery
51
Malfunction in memory of block ECM
52
The underestimated pressure of the relay of the pump of additional air
53
The overestimated pressure of the relay of the pump of additional air
54
Incorrect pressure of the resistor of adjustment of level CO (engines E16NZ)
55
It is faulty ECM
56
The underestimated pressure on valve IAC
57
The overestimated pressure on valve IAC
61
The underestimated pressure on the valve of a purge of an adsorber of system EVAP
62
The control system of a purge of an adsorber of system EVAP is faulty
63
The underestimated pressure on the module (DIS)
64
The underestimated pressure on the electronic block of management of ignition
66
Malfunction of a hose of gauge MAP
67, 68
On ECM there is no signal from gauge MAF
69
The underestimated pressure on gauge IAT
71
The overestimated pressure on gauge IAT
72
Rupture in a chain of the amplifier of ignition
75
The underestimated pressure of management of twisting moment АТ
76
Incorrect signal of management of twisting moment АТ
81
The underestimated/overestimated pressure on injector TBI/MFI
83
The wrong code of system иммобилизации the engine is absent or is entered
84
There is no system signal иммобилизации the engine
85
Incorrect signal of system иммобилизации the engine
87
The underestimated pressure of relay K/V
88
The overestimated pressure of relay K/V
92
Gauge CMP or its electroconducting is faulty
93
Malfunction of MIL/relay K/V or in management of twisting moment АТ

The list of codes of the malfunctions registered by system of electronic control by the engine

Multec, Simtec, Motronic

Code designation

Possible source of infringement

P0000
Absence of codes of malfunctions in memory of system
P0100
Infringement in a chain of a measuring instrument of weight of air MAF
P0105
Malfunctions in a chain of the gauge of absolute pressure (МАР)
P0110
Infringement in a chain of the gauge of temperature of soaked up air (IAT)
P0115
Absence or excessively low level of a signal of the gauge of temperature of a cooler (EATS)
P0120
Malfunctions in a chain of the gauge of position throttle заслонки (TPS)
P0130
Malfunction in a chain докаталитического a ljambda-probe (the right number of cylinders on the V-shaped engine)
P0135
Infringement in a heating chain докаталитического a ljambda-probe (the high voltage) (the right number of cylinders on the V-shaped engine is excessive)
P0150
Malfunction in a chain докаталитического a ljambda-probe (the left number of cylinders on the V-shaped engine)
P0170
Repauperization or reenrichment of an air-fuel mix (the right number of cylinders on the V-shaped engine)
P0190
Serviceability of functioning of the gauge of pressure of injection (on a fuel highway) / malfunction ТНВД is broken
P0195
Malfunction in a chain of the gauge of temperature of impellent oil
P0200
Malfunction in a chain of injection of fuel
P0201 - P0206
Malfunction in a chain of an injector of the cylinder 1 – 6 accordingly
P0230
Malfunction in a chain of the relay of management of the engine
P0325
The gauge of a detonation 1 (the right number of cylinders on the V-shaped engine) is faulty
P0330
The gauge of a detonation 2 (the left number of cylinders on the V-shaped engine) is faulty
P0335
Malfunction in a chain of the gauge of position of cranked shaft СКР
P0340
Malfunction in a chain of the gauge of position of camshaft СМР
P0351
Signal of ignition of cylinders 1 and 4
P0352
Signal of ignition of cylinders 2 and 3
P0400
Excessiveness or insufficiency of intensity рециркуляции the fulfilled gases (EGR)
P0403
Malfunction in valve EGR chain
P0410
Malfunction of the relay of an e/magnet of system подмешивания additional air
P0412
Malfunction in a chain of the valve of system подмешивания additional air
P0440
Malfunction in a chain of the gauge of position of the valve рециркуляции the fulfilled gases (EGR)
P0443
Malfunction in a chain of the valve of management of a purge of coal adsorber EVAP
P0500
Malfunction in a chain of the gauge of speed of car VSS
P0505
Malfunction in a chain of gauge IAC of stabilisation of turns of idling
P0560
Malfunction in system of onboard power supplies
P0602
Error of programming of the module of management
P0606
Processor RSM refusal
P0703
Malfunction in a chain of the gauge-switch of position of a brake pedal / of the converter of rotation
P0704
Malfunction in an entrance contour of a chain of the gauge-switch of coupling
P0725
Failures in giving of a signal of turns of the engine/gauge of position коленвала
P1100
The gauge of measurement of an air stream (MAF)
P1110
Malfunction of a chain of the electromagnetic valve № 1 managements of air of the inlet pipeline
P1111
Malfunction of a chain of the electromagnetic valve № 2 managements of air of the inlet pipeline
P1120
Incorrect signal of the gauge And position of a pedal of an accelerator / absolute pressure in the pipeline (MAP), air leaks
P1122
Incorrect signal of the gauge In positions of a pedal of an accelerator
P1125
The valve of adjustment of dump турбокомпрессора
P1130
Malfunction in a chain of electroconducting of a warmed up ljambda-probe (HO2S) 1 number of cylinders
P1170
Malfunction of management of mix structure (МС) in an inlet path of 1st of some cylinders (power supply system)
P1171
Malfunction of management of mix structure (МС) in an inlet path of 1st of some cylinders (power supply system), - mix repauperization at engine work under loading
P1173
Activation of system of protection of the engine from an overheat, oil temperature / a cooling liquid/fuel
P1180
The gauge of temperature of fuel
P1220
Management infringement газораспределением injection systems
P1229
The raised pressure of a food of the operating relay of the engine
P1230
The lowered pressure of a food of the operating relay of the engine
P1231
The operating relay of the fuel pump
P1300
Malfunction in a chain of electroconducting of the gauge of a stock of the fuel, full development of a stock
P1326
Infringement in conducting of the gauge of a detonation/ECM - the cylinder № 1
P1327
Infringement in conducting of the gauge of a detonation/ECM - the cylinder № 2
P1328
Infringement in conducting of the gauge of a detonation/ECM - the cylinder № 3
P1329
Infringement in conducting of the gauge of a detonation/ECM - the cylinder № 4
P1335
ТНВД - the incorrect information on engine turns
P1345
The gauge of position of entrance shaft ТНВД
P1372
Malfunction in a chain of electroconducting of the gauge of position of a cranked shaft (CKP)
P1404
Infringement of serviceability of functioning of the valve EGR/malfunction in a chain of its electroconducting
P1405
Malfunction or infringement in conducting of the gauge of position of electromagnetic valve EGR
P1410
The pump relay подмешивания air in an exhaust
P1481
Malfunction in a chain of electroconducting of the relay of 1 electromotor of a drive of the fan of system of cooling
P1482
Malfunction in a chain of electroconducting of the relay 2 electromotors of a drive of the fan of system of cooling
P1483
Malfunction in a chain of electroconducting of the relay 2 electromotors of a drive of the fan of system of cooling
P1500
Malfunction in a chain of electroconducting of an electronic control system of a throttle (ETS) / refusal ECM
P1501
Program error of the module of management иммобилизатора
P1501
The management module иммобилизатора
P1502
Signal loss in a chain of the module of management иммобилизатора
P1502
Иммобилизатор - absence of a signal
P1503
Error of a signal of the module of management immobilizatora/attempt of application of not verified key
P1503
Иммобилизатор - an incorrect signal
P1508
Breakage/short circuit on weight in a chain of electroconducting of the valve of stabilisation of turns of idling (IAC)
P1509
Short circuit on + in a chain of electroconducting of the valve of stabilisation of turns of idling (IAC)
P1510
Malfunction in a chain of electroconducting of the gauge-switch of the closed position throttle заслонки (СТР)
P1515
Malfunction in a chain of electroconducting of the valve of the IAC/gauge of position of a pedal of gas (АPР)
P1520
Refusal of giving of pressure of a food of an electronic control system by a throttle (ETS) / refusal ECM
P1523
Malfunction in a chain of electroconducting ETS
P1525
Malfunction in chains of electroconducting ETS, system transition in emergency operation
P1526
Malfunction in a chain of electroconducting ETS, - refusal of a mode of adaptation
P1530
Malfunction in a chain of electroconducting of the relay of switching-off To/in/refusal ECM
P1540
Malfunction in a chain of electroconducting of the gauge of pressure of a coolant To/in/refusal ECM
P1546
Signal loss in a chain of electroconducting of coupling of compressor K/V, - signal loss
P1550
System ETS transition in emergency operation in a combination to others DTC
P1551
Refusal of monitoring of a twisting moment of the engine of system ETS, - constant excess of admissible value
P1555
Improbable signal of the gauge And position throttle заслонки (TPS)/termoanemometricheskogo the gauge of weight of air (MAF), owing to leaks of air/blocking of a hose
P1560
The battery high voltage, damage of conducting of the generator is excessive
P1571
Malfunction in a chain of electroconducting of the gauge of position of a pedal of a foot brake (ВВР)
P1600
Error of programming of the module of engine management (ECM)
P1601
Excessively heat ECM
P1602
Error of memory RAM of block ECM in management chains on a detonation
P1604
Malfunction of the module of engine management ECM
P1605
The program coding of the module of engine management ECM
P1606
Refusal ECM
P1610
Program error of the module of management иммобилизатора
P1611
Error of introduction of a security code of the module of management иммобилизатора
P1612
Infringement of correctness/absence of a signal of the module of management иммобилизатора
P1613
Infringement of correctness/absence of a signal of the module of management иммобилизатора
P1614
Infringement of correctness of a signal of the module of management immobilizatora/attempt of application of not verified key
P1615
Infringement of correctness of a signal of the module of management immobilizatora/kuzovnogo the management module
P1616
Infringement of correctness of a signal of the module of management immobilizatora / the instrument module of management
P1618
Refusal ECM
P1620
Malfunction in a chain of target pressure (5) modules of management of a throttle/gauge APP/malfunction in feed circuit ECM, - excess of admissible value/refusal of the managing director of relay/refusal ECM
P1622
Infringement of serviceability of functioning of the relay of the fuel pump
P1625
Refusal ECM / the operating relay of the engine - absence of pressure on the plug 3 ECM
P1627
Refusal ECM
P1630
Regulator of quality of fuel
P1631
The module of management ТНВД
P1635
Refusal ECM/Модуля of management by preheat
P1640
Malfunction in a chain of electroconducting ECM/MIL/signals of the RPM/expense of fuel / refusal ECM
P1650
Malfunction in a chain of the indicator of service
P1651
The tyre of given CAN
P1690
Malfunction in a chain of a control lamp of refusals (MIL)
P1694
Control lamp of preheat
P1700
Signal of service of the engine ECM/infringement of serviceability of the module of management by transmission (TCM)
P1705
Wrong signal of the gauge-switch PNP/refusal TCM
P1740
Refusal of management by twisting moment АТ/ECM/TCM
P1743
Infringement of serviceability of functioning of coupling of the converter of rotation/transmissionnye of vibration
P1760
Excess of pressure of ignition as a result of infringement of serviceability of functioning of the battery or the generator
P1780
Malfunction in a chain of electroconducting TPS/infringement of serviceability of functioning антипробуксовочной systems (HARDWARE) / refusal TCM
P1781
Malfunction in a chain of electroconducting of the ECM/TCM/tyre of the data a CAN/signal of the valid twisting moment
P1790
The tyre of data CAN, - communication infringement between ECM and TCM
P1792
The tyre of data CAN, - communication infringement between ECM and TCM
P1800
Excess of pressure of ignition as a result of infringement of serviceability of functioning of the battery or the generator
P1813
Refusal ECM/TCM, - a signal of twisting moment АТ
P1835
Malfunction in a chain of electroconducting of the gauge-switch of activation of a mode kickdown
P1842
Inadmissible signal of the gauge TPS/refusal ECM/TCM
P1843
Inadmissible signal of the gauge of temperature of a cooling liquid of the engine (ECT) / refusal ECM/TCM
P1844
Inadmissible signal of management of twisting moment/refusal ECM/TCM
P1845
Refusal in an alarm chain of management of a twisting moment AT/MALFUNCTION in a chain of electroconducting TCM
P1847
Absence of multiplex signal TCM
P1850
Refusal in a chain of electroconducting of the electromagnetic valve of switching (SS) "With", - braking activation
P1860
Refusal in a chain of electroconducting of the electromagnetic valve of coupling of the hydrotransformer (TCC)
P1870
Mechanical refusal TCC
P1890
Tyre CAN, - malfunction in lines of communication ECM-TCM/malfunction in a chain of electroconducting TPS
P1895
Malfunction in a chain of electroconducting ECM/TCM, - a signal of the valid twisting moment
U2100
Electric refusal in the tyre of given CAN
U2101
Program refusal of tyre CAN
U2103
Tyre CAN/ECM refusal
U2104
Tyre CAN/ECM refusal
U2105
Communication refusal in the tyre of given CAN
U2106
Tyre CAN, - refusal in lines of communication ECM-TCM
U2107
Tyre CAN, - malfunction in lines of communication the ECM-module of management of refusals
U2108
Tyre CAN, - malfunction in lines of communication the ECM-module of management the management ABS-module антипробуксовочной systems (HARDWARE)

Start and charge systems
System type 12-voltnaja, with grounding On a negative pole

The battery
Pressure of a charge, In

Norm
12

Capacity, Ach

Norm
36, 45 or 60

The alternating current generator

Выступание brushes from the holder, mm
5
The manufacturer
Bosch
Nominal working pressure (at a room temperature), In
14
Adjustable pressure *, In
13.5 14.5

* Adjustable pressure should be established within 1 minute at 4000 rpm

Starter
The manufacturer
Valeo

Efforts of a tightening of carving connections, Nanometer

Petrol engines

Bolts of fastening of the module of ignition
8
Bolts of fastening of the generator to the bottom holder
35
Bolts of fastening of the generator to the top holder
20
Generator fixture on engines of 1.0 l
40
Bolts of fastening of a starter
25

Diesel engines

Candles накаливания
20
Generator fastening
50
Bolts of fastening of a starter
The bottom bolt
45
The top bolt
75