Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and safety measures
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and the other fixed glasses
   Removal and installation of an overlay and bearing beam of bumpers
   Removal and installation of a decorative lattice of a radiator (model since 03.1997 вып.)
   Removal and installation локера a wheel arch
   Removal and panel installation обтекателя a windscreen
   Removal and cowl installation
   Replacement of loops of a cowl
   Removal and installation of a forward wing
   Replacement of an overlay of a back wheel arch (model Corsa and Combo)
   Removal and installation of facing of doors
   Removal and installation of glass of a forward door
   Removal and installation of glass of a back door (model Corsa)
   Removal and installation стеклоподъемника
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock of a forward door
   Removal and installation of the lock of a door
   Protection against freezing of locks and consolidations
   Removal and installation of an external mirror and the e/motor of its drive
   Removal and installation of the case of an external mirror
   Removal, installation and door adjustment
   Removal and installation of a door of a back (model Corsa and Tigra)
   Removal and installation of the lock of a door of a back (model Corsa and Tigra)
   Removal, installation, dismantling and assemblage of the external handle and the cylinder of the lock of a door of a back (model Corsa)
   Натяжитель a seat belt
   Security measures at the reference with emergency преднатяжителем a seat belt and a lateral pillow of safety
   Removal and installation of a forward seat
   Removal and installation of a back seat
   Removal and installation of the central console
   Removal and installation of lateral facing of a foot well of the forward passenger
   Removal and installation of a ware box
   Removal and installation of an internal mirror and installation of a plate of its fastening
   Removal and installation of the panel of devices
   The sdvizhnaja panel of a roof
+ Onboard electric equipment


Removal and installation of facing of doors

Cars from 09.1998 of release can be completed with a lateral pillow of the safety which have been built in on each side of backs of seats of the driver and the forward passenger. Seats with a lateral pillow of safety are marked by white stripes with a red inscription AIRBAG. The gauge of a pillow of safety is from each party behind door facing. On the cars equipped with lateral pillows of safety observe safety rules at work with elements of lateral pillows of safety and emergency натяжителей belts.

Removal of facing of a forward door (all models)

 PERFORMANCE ORDER

  1. Cautiously disconnect an overlay of the internal handle of opening of a door. Disconnect the handle (arrows). Separate socket ВЧ dynamics (1).

Bolts of fastening of the handle (arrow) and socket ВЧ dynamics (1)

  1. Squeeze out from within doors of the driver the switch of an electric regulator of an external mirror, separate its socket and remove the switch.

Removal of the switch of an electric regulator of an external mirror

  1. Turn out bolts of fastening of a pocket of a door and wring out a wide screw-driver two clamps At a corresponding complete set separate a socket of electroconducting of the switch electric стеклоподъемника and remove a door pocket.

Fixture of a pocket of a door
A — Combo
B — the Sedan

  1. On model Combo wring out clamps of a triangular overlay of an external mirror from a door frame in its top part.

Clamps of an overlay of an external mirror

  1. At a corresponding complete set remove the handle of moving of glass of a forward door. For this purpose wring out tool OPEL-KM-317-A a wire clip. It is possible to apply pincers HAZET-799 also. If specified above tools is not present, wring out a clip a narrow screw-driver in an arrow direction.

Removal of the handle of moving of glass of a forward door

  1. Remove the handle from its axis. If at removal the spring has been completely squeezed out, again press a spring into a handle groove. Remove a plastic washer.
  2. Remove by means of plastic шпателя an internal sealant of glass of a forward door.

Removal of an internal sealant of glass

  1. On models Corsa and Combo turn out bolts (arrows).

Bolts of fastening of facing (model Corsa and Combo)

  1. On model Tigra turn out three bolts from the bottom edge of a door. Disconnect by means of plastic шпателя facing from a door behind and in front, having opened thus clamps.

Bolts and facing clamps (model Tigra)

  1. Remove facing upwards through the button of blocking of a door.
  2. If it is necessary, cautiously remove a sealing film from a door frame. Preliminary wring out clamps (arrows).

Clamps of a sealing film

Removal of facing of a back door (model Corsa)

 PERFORMANCE ORDER

  1. Disconnect an overlay of the internal handle of opening of a door (3), turn out screws of fastening and remove the handle of a back door (1).

The components, facings of a back door stirring to removal

  1. Remove the handle of moving of glass of a back door (2).
  2. Remove a triangular overlay in a back part of a door.

Removal of a triangular overlay

  1. Turn out bolts of fastening (arrow) and remove facing upwards.

Bolts of fastening of facing

  1. Remove upwards internal consolidation of glass of a back door.

Installation

 PERFORMANCE ORDER

  1. Accurately paste a sealing film to a door frame. Ruptures stick with an adhesive tape.

On cars with a lateral pillow of safety replace the damaged film. It is of great importance for correct operation of a lateral pillow of safety.

  1. Connect sockets of electroconducting of switches of a regulator of an external mirror and стеклоподъемника (at a corresponding complete set).
  2. Put on an upholstery through the inclusion button, expose it on a frame of a door and fix.
  3. Fix a pocket of a door screws.
  4. Fix the door handle. Connect socket ВЧ dynamics.
  5. At a manual drive of glass of a door put on a handle axis a plastic washer the high party in a facing direction.
  6. Put on an axis the handle of moving of glass of a door and slam her hand. Thus the spring lock should enter into a groove on an axis. The handle should be turned downwards at the closed window.
  7. Press an internal sealant of glass.
  8. Fix a triangular overlay and door handles.