Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation

Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and safety measures
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and the other fixed glasses
   Removal and installation of an overlay and bearing beam of bumpers
   Removal and installation of a decorative lattice of a radiator (model since 03.1997 вып.)
   Removal and installation локера a wheel arch
   Removal and panel installation обтекателя a windscreen
   Removal and cowl installation
   Replacement of loops of a cowl
   Removal and installation of a forward wing
   Replacement of an overlay of a back wheel arch (model Corsa and Combo)
   Removal and installation of facing of doors
   Removal and installation of glass of a forward door
   Removal and installation of glass of a back door (model Corsa)
   Removal and installation стеклоподъемника
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock of a forward door
   Removal and installation of the lock of a door
   Protection against freezing of locks and consolidations
   Removal and installation of an external mirror and the e/motor of its drive
   Removal and installation of the case of an external mirror
   Removal, installation and door adjustment
   Removal and installation of a door of a back (model Corsa and Tigra)
   Removal and installation of the lock of a door of a back (model Corsa and Tigra)
   Removal, installation, dismantling and assemblage of the external handle and the cylinder of the lock of a door of a back (model Corsa)
   Натяжитель a seat belt
   Security measures at the reference with emergency преднатяжителем a seat belt and a lateral pillow of safety
   Removal and installation of a forward seat
   Removal and installation of a back seat
   Removal and installation of the central console
   Removal and installation of lateral facing of a foot well of the forward passenger
   Removal and installation of a ware box
   Removal and installation of an internal mirror and installation of a plate of its fastening
   Removal and installation of the panel of devices
   The sdvizhnaja panel of a roof
+ Onboard electric equipment

Removal and cowl installation

For cowl removal the assistant is required.


  1. Open and fix it in completely open position by a persistent bar.
  2. Disconnect a hose from the pump стеклоомывателя. For this purpose take out the pump from the tank.

Detachment of a hose from the washer pump

  1. Mark position of bolts of fastening of a cowl on loops.
  2. Turn out bolts of fastening of a cowl to both loops and remove a cowl.

Bolts of fastening of a cowl

  1. Establish a cowl and tighten fixing bolts according to earlier put labels.
  2. Put on a hose the pump стеклоомывателя and insert the pump into the tank.

Installation of a new cowl


  1. Screw a rubber emphasis (1) and paste демпфирующие rubber linings (2). Adjust height of a cowl concerning wings.

Rubber emphasis (1) and linings (2)

  1. Expose a cowl in a horizontal plane without a hook, being guided by backlashes concerning a windscreen, wings and headlights.
  2. Establish a hook (4) with a spring (3) and rivet it.

Installation of a hook (4) with a spring (3)

  1. Screw a carving support in gathering in a cowl and establish on distance х (from sheet of a cowl to edge of the top washer). Then, keeping a support a key, tighten a nut (2).

Assemblage of a carving support of a cowl
1 — the Washer
2 — the Nut
3 — the Washer
4 — the Spring
5 — the Washer
6 — the Carving support
x — 40 45 mm

  1. Fix a hose стеклоомывателя in the holder. The hose should not be pressed at the closed cowl.