Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation

Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and safety measures
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and the other fixed glasses
   Removal and installation of an overlay and bearing beam of bumpers
   Removal and installation of a decorative lattice of a radiator (model since 03.1997 вып.)
   Removal and installation локера a wheel arch
   Removal and panel installation обтекателя a windscreen
   Removal and cowl installation
   Replacement of loops of a cowl
   Removal and installation of a forward wing
   Replacement of an overlay of a back wheel arch (model Corsa and Combo)
   Removal and installation of facing of doors
   Removal and installation of glass of a forward door
   Removal and installation of glass of a back door (model Corsa)
   Removal and installation стеклоподъемника
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock of a forward door
   Removal and installation of the lock of a door
   Protection against freezing of locks and consolidations
   Removal and installation of an external mirror and the e/motor of its drive
   Removal and installation of the case of an external mirror
   Removal, installation and door adjustment
   Removal and installation of a door of a back (model Corsa and Tigra)
   Removal and installation of the lock of a door of a back (model Corsa and Tigra)
   Removal, installation, dismantling and assemblage of the external handle and the cylinder of the lock of a door of a back (model Corsa)
   Натяжитель a seat belt
   Security measures at the reference with emergency преднатяжителем a seat belt and a lateral pillow of safety
   Removal and installation of a forward seat
   Removal and installation of a back seat
   Removal and installation of the central console
   Removal and installation of lateral facing of a foot well of the forward passenger
   Removal and installation of a ware box
   Removal and installation of an internal mirror and installation of a plate of its fastening
   Removal and installation of the panel of devices
   The sdvizhnaja panel of a roof
+ Onboard electric equipment

Removal and installation of glass of a forward door



  1. Remove facing of a door with a sealing film. Watch to tearing a film, otherwise it is required to replace it.
  2. Completely close a window. Mark position of screws of fastening directing glasses.

Models Corsa and Combo


  1. Turn out screws of fastening directing glasses (arrow) and remove a rubber sealant Remove directing downwards.

Screws of fastening directing glasses
A — Combo
B — Corsa

  1. Lower glass downwards, as is shown in an accompanying illustration.

Directing glasses (1), ползуны стеклоподъемника (2) and bolts of its fastening directing (3)

  1. Turn out bolts of fastening directing (3) стеклоподъемника. On models from 09.1993 of release turn out screws of fastening directing and take out it with a rubber sealant.
  2. Take out ползуны стеклоподъемника (2) of directing glasses (1).

Model Tigra


  1. On model Tigra turn out fixture forward and back directing glasses. Pull out ползуны стеклоподъемника from a lobby directing.

Fixture directing glasses

All models


  1. Incline a window forward and pull out upward from a door.



  1. Insert a windowpane from above into window mine.
  2. Insert ползуны ножницеобразного стеклоподъемника into the directing.
  3. Attach directing on the established labels. If necessary, before a bolt tightening adjust window position. For this purpose use bolts and pull a window upwards and downwards. The window itself will rise into place after that screw up bolts.
  4. Insert back directing and screw up. Press on sealing rubber.
  5. Establish door facing.
  6. Establish electric стеклоподъемник. For this purpose close all doors and include ignition. Close windows the button. Keep the button pressed in position of the closed window not less than 2 seconds