Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and safety measures
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and the other fixed glasses
   Removal and installation of an overlay and bearing beam of bumpers
   Removal and installation of a decorative lattice of a radiator (model since 03.1997 вып.)
   Removal and installation локера a wheel arch
   Removal and panel installation обтекателя a windscreen
   Removal and cowl installation
   Replacement of loops of a cowl
   Removal and installation of a forward wing
   Replacement of an overlay of a back wheel arch (model Corsa and Combo)
   Removal and installation of facing of doors
   Removal and installation of glass of a forward door
   Removal and installation of glass of a back door (model Corsa)
   Removal and installation стеклоподъемника
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock of a forward door
   Removal and installation of the lock of a door
   Protection against freezing of locks and consolidations
   Removal and installation of an external mirror and the e/motor of its drive
   Removal and installation of the case of an external mirror
   Removal, installation and door adjustment
   Removal and installation of a door of a back (model Corsa and Tigra)
   Removal and installation of the lock of a door of a back (model Corsa and Tigra)
   Removal, installation, dismantling and assemblage of the external handle and the cylinder of the lock of a door of a back (model Corsa)
   Натяжитель a seat belt
   Security measures at the reference with emergency преднатяжителем a seat belt and a lateral pillow of safety
   Removal and installation of a forward seat
   Removal and installation of a back seat
   Removal and installation of the central console
   Removal and installation of lateral facing of a foot well of the forward passenger
   Removal and installation of a ware box
   Removal and installation of an internal mirror and installation of a plate of its fastening
   Removal and installation of the panel of devices
   The sdvizhnaja panel of a roof
+ Onboard electric equipment


Removal and installation стеклоподъемника

Installation manual and electric стеклоподъемника is identical. Electric стеклоподъемник has electronic control, i.e. by short-term pressing the switch (less than 0.4) glass can интервально move. Is as a result longer switch pressing (longer 0.4) glass automatically moves before full opening or closing. If glass above the window middle encounters any obstacle at once stops and opens a little. E/motors стеклоподъемников are equipped by the overload switch in case glass will jam, for example, owing to its icing.

Removal

 PERFORMANCE ORDER

  1. Remove door facing.
  2. Remove a protective film. Watch that the film thus has not torn. The torn film stick or replace.
  3. Establish glass at level of the top assembly aperture and fix its two plastic wedges.
  4. Separate a socket at doors.
  5. On models Corsa and Combo turn out bolts of fastening directing (4), preliminary having marked their position. Take out from directing glasses (2) ползуны the lift (3).

Directing (2), bolts of its fastening (4) and the lift (3)

  1. On model Tigra turn out rivets of fastening directing стеклоподъемника, preliminary having marked their position. Take out from directing glasses ползуны the lift.
  2. Drill rivets (1) (address to an illustration) - are shown стеклоподъемники with a manual drive of fastening has flown down a drill in diameter of 8.5 mm and beat out them выколоткой back.

Thus do not damage external sheet of a door.

  1. Take out стеклоподъемник from a door.

Installation

 PERFORMANCE ORDER

  1. Before installation new стеклоподъемника check up its work. For this purpose establish the handle of a drive or connect the e/motor and include стеклоподъемник.
  2. Grease ползуны стеклоподъемника консистентной with greasing and insert into the directing.
  3. Приклепайте the lift to a door steel rivets in the size 4.8 х 11 mm.
  4. It is alternatively possible to fix стеклоподъемник bolts and nuts. Nuts grease with fixing hermetic.
  5. Connect electroconducting.
  6. Remove plastic wedges.
  7. Adjust management electronics стеклоподъемником. For this purpose close all doors and include ignition. Windows close by means of the switch. Switches in position of closing of a window keep pressed at least 2 with.
  8. Check up work of a manual drive стеклоподъемника. Glass should rise and fall easily.
  9. Paste a protective film and establish door facing.