Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
- Brake system
   The general information
   System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
   Prorolling of brake system
   Check of a condition and replacement of brake lines and hoses
   Replacement колодок disk brake mechanisms of forward wheels
   Removal and installation of brake boots
   Replacement of brake overlays of drum-type brakes
   Condition check, removal and installation of a brake disk
   Removal, check of a condition and installation of a brake drum
   Removal, regenerative repair and installation of supports of disk brake mechanisms of forward wheels
   Removal, service and installation of wheel cylinders of drum-type brake mechanisms of back wheels
   Check of serviceability of functioning and tightness of the vacuum amplifier of brakes
   Replacement and check of the vacuum pump of the servo-driver of the brake amplifier (diesel models)
   Adjustment of a drive of a lay brake
   Removal and installation of cables of a drive of a lay brake
   Replacement of the gauge-switch of stoplights
   The pressure valve-regulator in hydraulic contours of brake mechanisms of back wheels
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal, check of a condition and installation of a brake drum

Remember that developed in the course of work of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system by gasoline or solvents on an oil basis, - apply only firm cleaners or methyl spirit!

Removal

 PERFORMANCE ORDER

  1. Turn out bolts of fastening of back wheels, поддомкратьте a back of the car and establish it on props. Remove back wheels.
  2. Release a lay brake.
  3. On models Corsa B and Tigra remove a screw-driver a nave cover. Unbend flat-nose pliers lock шплинт and take out it, give an adjusting nut. Remove a brake drum. Thus watch that the press washer and the external bearing have not fallen.
  4. On model Combo turn out the lock screw of a brake drum and remove a drum If the drum is strongly linked to an aligning fillet of a nave, slightly knock on it with a plastic hammer. The bearing of a wheel of model Combo is in a separate nave whereas on other models considered in the present Management, the wheel bearing is directly in a brake drum.

Отдавание the fixing screw of a brake drum

  1. If the brake drum does not act in film, remove a stopper on an underside of a brake board and press a screw-driver the lever of a lay brake so that it adjoined to a wall brake колодки Thanks to it a returnable spring can delay brake колодки and it will be possible to remove a brake drum. If necessary disconnect a cable of a lay brake.

Pressing by a screw-driver the lever of a lay brake

Check

 PERFORMANCE ORDER

  1. Сметите from components of the brake mechanism accumulated on from surfaces a dust.

Remember that developed in the course of work of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system by gasoline or solvents on an oil basis, - apply only firm cleaners or methyl spirit!

  1. Check up a condition of an internal working surface of a drum, in case of revealing of furrows or deep scratches replace drums of both brake mechanisms.
  2. Insignificant defects can be eliminated a way проточки a drum provided that the maximum admissible size of its diameter will not be exceeded.

Both drums are subject проточке on identical depth. Composers of the present Management recommend after проточки to make drums replacement of brake boots.

Installation

 PERFORMANCE ORDER

  1. On models Corsa B and Tigra rearrange serviceable bearings of wheels from old brake drums in new (see Has undressed Removal and installation of brake boots).
  2. On models Corsa B and Tigra establish brake drums and adjust a backlash of bearings of wheels (the Section Replacement of brake overlays of drum-type brakes see).
  3. On model Combo clear a carving aperture for the lock screw and if necessary cautiously pass its tap. Grease the lock screw with fixing hermetic, for example, OPEL 1510177. Establish a brake drum on a nave so that the aperture for the lock screw coincided with an aperture in a nave. Screw the lock screw and tighten it with effort of 4 Nanometers.
  4. Grease with a thin layer of greasing aligning corbels of brake drums. Establish back wheels, lower the car on the earth and tighten bolts of fastening of wheels cross-wise with effort of 110 Nanometers.
  5. Press a brake pedal approximately 20 25 times so that it was not audible any more a clicking of the adjusting lever. It means that brake колодки have occupied the working position.
  6. Adjust a lay brake (the Section Adjustment of a drive of a lay brake see).
  7. Check up level of a brake liquid in the tank and if necessary, add it to mark MAX.