Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
- Brake system
   The general information
   System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
   Prorolling of brake system
   Check of a condition and replacement of brake lines and hoses
   Replacement колодок disk brake mechanisms of forward wheels
   Removal and installation of brake boots
   Replacement of brake overlays of drum-type brakes
   Condition check, removal and installation of a brake disk
   Removal, check of a condition and installation of a brake drum
   Removal, regenerative repair and installation of supports of disk brake mechanisms of forward wheels
   Removal, service and installation of wheel cylinders of drum-type brake mechanisms of back wheels
   Check of serviceability of functioning and tightness of the vacuum amplifier of brakes
   Replacement and check of the vacuum pump of the servo-driver of the brake amplifier (diesel models)
   Adjustment of a drive of a lay brake
   Removal and installation of cables of a drive of a lay brake
   Replacement of the gauge-switch of stoplights
   The pressure valve-regulator in hydraulic contours of brake mechanisms of back wheels
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of cables of a drive of a lay brake

The mechanism of a lay brake of models Corsa and Tigra

1— The Lever of a lay brake
2 — Directing a cable
3 — the Short (right) cable

4 — the Jack
5 — the Long (left) cable
6 — Lengthening with a stopper

Models Corsa and Tigra

The right party (short cable)

 PERFORMANCE ORDER

  1. Disconnect the jack of a lay brake from a hummock of a drive of a brake. Thus keep pincers a carving bar from проворачивания Remove outside the rubber buffer.

Keeping of a carving bar

  1. Remove a cable of a drive of a lay brake from a back suspension bracket directing on a beam.
  2. Remove the right brake boot (see Has undressed Removal and installation of brake boots).
  3. Take out the plastic plug from a brake board and extend a cable.
  4. Installation is made upside-down.

Left-hand side (long cable)

 PERFORMANCE ORDER

  1. Measure and write down length of a carving of the jack of a cable of a drive of a lay brake Remove the rubber buffer and turn out the jack. Thus keep the jack a wrench from проворачивания.

Measurement of length of a carving of the jack

  1. Remove a thermofilter from the muffler.
  2. Release a cable of a drive of a lay brake from the extension piece (marksman) and disconnect it.

Fastening of a cable of a lay brake to the extension piece

  1. Take out a cable from the holder and directing on a back suspension bracket.
  2. Remove the left brake boot (see Has undressed Removal and installation of brake boots).
  3. Take out the plastic plug from a brake board and extend a cable.
  4. Installation is made upside-down. Watch, that the length of a carving of the jack corresponded to the value written down at removal.

Model Combo

 PERFORMANCE ORDER

  1. Remove a brake drum (see Has undressed Removal and installation of brake boots).
  2. Give fixture of system of release of the fulfilled gases around a cable of a drive of a lay brake.
  3. Remove a thermofilter from the bottom.
  4. Give a nut (marksman) of the jack of a lay brake.

Nut of the jack of a lay brake

  1. Take out cables from the directing.

Extraction of cables from the directing

  1. Remove plastic plugs from the holder. Unbend a bit directing a cable (marksman) on the bottom and back springs of a suspension bracket and remove a cable.

Plastic plugs

  1. Press forward the lever of a lay brake on brake колодке and remove a cable.

Cable removal

  1. Take out the plastic plug from a brake board and extend a cable.
  2. Establish a cable of a drive of a lay brake in return sequence and adjust it.