Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
- Brake system
   The general information
   System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
   Prorolling of brake system
   Check of a condition and replacement of brake lines and hoses
   Replacement колодок disk brake mechanisms of forward wheels
   Removal and installation of brake boots
   Replacement of brake overlays of drum-type brakes
   Condition check, removal and installation of a brake disk
   Removal, check of a condition and installation of a brake drum
   Removal, regenerative repair and installation of supports of disk brake mechanisms of forward wheels
   Removal, service and installation of wheel cylinders of drum-type brake mechanisms of back wheels
   Check of serviceability of functioning and tightness of the vacuum amplifier of brakes
   Replacement and check of the vacuum pump of the servo-driver of the brake amplifier (diesel models)
   Adjustment of a drive of a lay brake
   Removal and installation of cables of a drive of a lay brake
   Replacement of the gauge-switch of stoplights
   The pressure valve-regulator in hydraulic contours of brake mechanisms of back wheels
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Condition check, removal and installation of a brake disk

Condition check

Cars with engines capacity to 60 h.p. are equipped in front by integral brake disks. Cars with more powerful engines are equipped by ventilated disk brakes.


 PERFORMANCE ORDER

  1. Ослабьте bolts of fastening of wheels, поддомкратьте the car also establish it on props. Remove a corresponding wheel, then return pair of wheel bolts for the purpose of fixing of a brake disk (if the screw of fastening of a disk will not turn out yet, necessity for installation of bolts disappears).
  2. Remove a brake support (see Has undressed Removal, regenerative repair and installation of supports of disk brake mechanisms of forward wheels) and tie up it aside a wire to a suspension bracket element, without disconnecting a brake hose.
  3. Make visual check of a condition of a working surface of a disk. Easy defects can be eliminated by means of a fine-grained emery paper. For removal of deep furrows it is necessary to subject a disk проточке. Remember that disk survey should be made from its both parties.
  4. If during braking pulsations of a pedal of a foot brake were noticed, it is necessary to estimate size of lateral palpation of a brake disk. Fix циферблатный a measuring instrument плунжерного type on distance about 13 mm from external edge of a disk. Null the device and start to rotate a disk. The result of measurement should not fall outside the limits stipulated in Specifications (the Head Brake system) an admissible range, otherwise it is necessary to give a disk in проточку.

Measurement of size of lateral palpation of a brake disk

Composers of the present Management recommend to make проточку disks without dependence from their condition for the purpose of removal from working any surfaces of defects. As a last resort it is possible to be limited to processing of a disk by a fine-grained emery paper.

  1. At проточке a disk it is necessary to give particular attention to observance of requirements of Specifications in the Head Brake system to its minimum admissible thickness. On a face surface of a disk corresponding marks are provided. Measurement of a thickness of a disk is made by means of a micrometer.

Measurement of a thickness of a brake disk

Removal

 PERFORMANCE ORDER

  1. Turn out the wheel bolts established at check of a disk.
  2. Remove a forward support (see Has undressed Removal, regenerative repair and installation of supports of disk brake mechanisms of forward wheels) with brake колодками and an arm of fastening and take him aside, having tied up to a rack.

Support removal

  1. Turn out the fixing screw and remove a brake disk from a wheel nave.

Отдавание the screw of fastening of a brake disk

Installation

 PERFORMANCE ORDER

  1. Installation is made in an order, the return to an order of dismantle of components. Before installation make sure of absoluteness of cleanliness and dryness of interfaced surfaces of a disk and a nave. Slightly grease a carving part of the screw of fastening of a disk with fixing hermetic.
  2. In summary establish brake колодки and a support of the brake mechanism (Sections Replacement колодок disk brake mechanisms of forward wheels and Removal, regenerative repair and installation of supports of disk brake mechanisms of forward wheels see).