Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
- Brake system
   The general information
   System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
   Prorolling of brake system
   Check of a condition and replacement of brake lines and hoses
   Replacement колодок disk brake mechanisms of forward wheels
   Removal and installation of brake boots
   Replacement of brake overlays of drum-type brakes
   Condition check, removal and installation of a brake disk
   Removal, check of a condition and installation of a brake drum
   Removal, regenerative repair and installation of supports of disk brake mechanisms of forward wheels
   Removal, service and installation of wheel cylinders of drum-type brake mechanisms of back wheels
   Check of serviceability of functioning and tightness of the vacuum amplifier of brakes
   Replacement and check of the vacuum pump of the servo-driver of the brake amplifier (diesel models)
   Adjustment of a drive of a lay brake
   Removal and installation of cables of a drive of a lay brake
   Replacement of the gauge-switch of stoplights
   The pressure valve-regulator in hydraulic contours of brake mechanisms of back wheels
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Check of a condition and replacement of brake lines and hoses

Approximately time in half a year, having lifted the car, check all flexible hoses connecting steel tubes of hydraulic contours with brake mechanisms of wheels on presence of cracks, signs of damage of a protective cover, traces of leaks of a liquid, swellings and other damages. Hoses are critical and most vulnerable making brake system, therefore their survey should be made with all carefulness - take advantage of a pocket small lamp and a small mirror. At revealing of any doubtful signs the suspected hose is subject to replacement.

Replaceable steel and flexible brake lines always can be got on a firm car repair shop the car companies-manufacturers, and also in firm shops of automobile accessories.

At all do not use as replaceable any tubes, except firm, specially intended for installation in a brake contour of your car.


 PERFORMANCE ORDER

  1. At installation of brake lines watch, that they settled down on removal not less than 20 mm from moving or vibrating components of a body, a suspension bracket or a steering drive.
  2. For отпускания штуцерных connections of flexible hoses with steel tubes of hydraulic lines use special накидные keys with a cutting head. After отпускания nuts remove a clamp and liberate a brake hose from a basic arm.
Отпускание штуцерных connections of flexible hoses with steel lines it should be made by means of special накидного a key with a cutting head
Having released a nut, remove a clamp and liberate a brake hose from an arm
  1. For a detachment of a brake hose from a support turn out a hollow bolt штуцерного connections and will throw out its old sealing washers, - at washer assemblage are subject to replacement without fail.

Sealing washers штуцерного connections

  1. Рассоединение two hoses it is made by means of usual рожковых keys. At joining of knots watch, that hoses were not overwound.
  2. Rigid tubes of hydraulic lines are usually fixed on all length special clamps. At line removal watch, that it has been liberated from all clips. Do not forget at installation of lines on the car to replace the failed clamps.
  3. At replacement of brake lines watch, that replaceable components in accuracy corresponded on the типоразмерным to characteristics to the old sections removed from the car. At all do not replace steel tubes copper!
  4. At installation of steel tubes watch reliability of their fixing in all provided arms, collars and clips. Do not suppose making of tubes excessively close from moving components of a suspension bracket and a steering drive.
  5. Having finished installation of new sections of hydraulic lines, check up liquid level in tank GTTS. In case of need make corresponding updating. Pump over brake system (the Section Prorolling of brake system see). Before to start car operation make sure of serviceability of functioning of brakes.