Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
- Engines
The general information
Check компрессионного pressure in cylinders and parametres of impellent oil
Diagnostics of a condition of the engine with vacuum gauge application
- Procedures of repair of petrol engines SOHC without their extraction from the car
Removal and cover installation газораспределительного the mechanism
Removal and installation of a pulley of a cranked shaft
Removal and installation of a cover of drive ГРМ
Removal and installation of a belt of drive ГРМ
Removal and installation of cogwheels of drive ГРМ
Replacement of an epiploon of a camshaft
Removal, check of a condition and installation of a camshaft from the case газораспределительного the mechanism
Removal, check of a condition and installation of valves
Removal and installation of a head of cylinders
Removal and pallet installation картера
Removal, service and installation of the oil pump
Removal, check of a condition and installation of a flywheel/privodnogo of a disk
Replacement of epiploons of a cranked shaft
+ Procedures of repair of petrol engines DOHC without their extraction from the car
+ Procedures of repair of diesel engines without their extraction from the car
+ The general and engine major repairs
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of cogwheels of drive ГРМ Camshaft cogwheel Removal
|
|
- Remove газораспределительный a belt (see Has undressed Removal and installation of a belt of drive ГРМ).
- Block a camshaft from проворачивания at отпускании the central bolt of its cogwheel. Make of two pieces of steel plates (one long, and one short) and three bolts with nuts вильчатое the adaptation for wheel deduction. One bolt use as axial, others two fix on the plug ends, - they are entered into gearing with apertures in a cogwheel. It is alternatively possible to uncover газораспределительного the mechanism (see Has undressed Removal and cover installation газораспределительного the mechanism) and to keep a shaft рожковым a key for лыски.
Blocking of a camshaft from проворачивания with the help вильчатого a clamp (it is alternatively possible to uncover газораспределительного the mechanism and to block a shaft for лыски рожковым a key)
- Turn out the central bolt and remove it from a shaft together with a washer. Remove a cogwheel. Check up landing density in a pin of an adjusting pin of a wheel, - in case of need take a pin and clean it in a reliable place.
|
|
Installation
|
|
- Before installation check up a condition of an epiploon of a camshaft. In case of revealing of traces of leaks or deterioration signs replace an epiploon (the Section Replacement of an epiploon of a camshaft see).
- Plant a cogwheel on a shaft pin, - track correctness of hit of a fixing pin in a reception aperture on a wheel.
At cogwheel landing track hit of an adjusting pin in a reception aperture
- Screw the central bolt with the washer put on it and tighten it with demanded effort, keeping a shaft from проворачивания one of the ways described in paragraph 2.
Tightening of the central bolt of fastening of a cogwheel of a camshaft (the shaft is kept from проворачивания for лыски, - cover ГРМ is removed)
- Establish a belt of drive ГРМ (see Has undressed Removal and installation of a belt of drive ГРМ), then, - if removed, - establish a cover газораспределительного the mechanism (see Has undressed Removal and cover installation газораспределительного the mechanism).
|
|
Cogwheel of a cranked shaft Removal
|
|
- Remove a belt of drive ГРМ (see Has undressed Removal and installation of a belt of drive ГРМ).
- Remove a cogwheel from a pin of a cranked shaft, - try to remember, the wheel has been established by what party.
- Check up reliability of landing in the groove шпонки, - in case of need take шпонку and clean it in a reliable place.
|
|
Installation
|
|
- If took, establish шпонку in a groove in a pin of a cranked shaft.
- Having tracked hit шпонки in шпоночный a groove, plant a cogwheel on a pin of a shaft label ВМТ outside.
- Establish a belt of drive ГРМ (see Has undressed Removal and installation of a belt of drive ГРМ).
|
|
|
|