Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
- Engines
The general information
Check компрессионного pressure in cylinders and parametres of impellent oil
Diagnostics of a condition of the engine with vacuum gauge application
- Procedures of repair of petrol engines SOHC without their extraction from the car
Removal and cover installation газораспределительного the mechanism
Removal and installation of a pulley of a cranked shaft
Removal and installation of a cover of drive ГРМ
Removal and installation of a belt of drive ГРМ
Removal and installation of cogwheels of drive ГРМ
Replacement of an epiploon of a camshaft
Removal, check of a condition and installation of a camshaft from the case газораспределительного the mechanism
Removal, check of a condition and installation of valves
Removal and installation of a head of cylinders
Removal and pallet installation картера
Removal, service and installation of the oil pump
Removal, check of a condition and installation of a flywheel/privodnogo of a disk
Replacement of epiploons of a cranked shaft
+ Procedures of repair of petrol engines DOHC without their extraction from the car
+ Procedures of repair of diesel engines without their extraction from the car
+ The general and engine major repairs
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, check of a condition and installation of a flywheel/privodnogo of a disk Removal Models with РКПП
|
|
- Remove transmission (the Manual 5-step box of a gear change or Automatic 4-step transmission see the Head) and coupling (Coupling and power shafts see the Head).
- By means of the suitable adaptation block a flywheel from проворачивания. With a paint or a marker mark position of a flywheel concerning a cranked shaft.
Flywheel blocking
- Turn out fixing bolts and remove a flywheel, - in case of need take advantage of the help of the assistant as the flywheel is heavy enough.
|
|
Models with АТ
|
|
- Remove transmission (the Manual 5-step box of a gear change or Automatic 4-step transmission see the Head).
- By means of the suitable adaptation block приводной a disk.
- Turn out fixing bolts and remove fixing plate and приводной a disk from a flange of a cranked shaft, - try to remember adjusting position of components.
|
|
Check
|
|
- Survey a flywheel/privodnoj a disk on presence of signs of deterioration or выкрашивания wreath teeths.
- Study a condition contacting to a disk of coupling of a working surface of a flywheel. In case of revealing of deep furrows or задиров, the flywheel can be given in проточку, however it will be more reasonable than it to replace.
- In the absence of confidence of an estimation of a condition of a flywheel, address for council to experts of car-care centre, and it is better, replace a flywheel.
|
|
Installation Models with РКПП
|
|
New bolts of fastening of a flywheel be required. |
|
|
- Smooth out interfaced surfaces of a flywheel and a cranked shaft, - track, that carving apertures in a shaft flange have been completely cleared of traces of old hermetic.
- Grease a carving part of fixing bolts with fixing hermetic, establish a flywheel and fix its bolts. At installation of the flywheel which was in the use track correctness of combination of the landing labels put in the course of dismantle.
- Block a flywheel a method used at removal. In a diagonal order in stages in regular intervals tighten all bolts with demanded effort.
- Establish coupling (Coupling and power shafts see the Head). Remove the adaptation blocking a flywheel and establish transmission (the Manual 5-step box of a gear change or Automatic 4-step transmission see the Head).
|
|
Models with АТ
|
|
- Smooth out interfaced surfaces приводного a disk and a cranked shaft, - track, that carving apertures in a shaft flange have been completely cleared of traces of old hermetic.
- Grease a carving part of fixing bolts with fixing hermetic, establish приводной a disk with a fixing plate and fix components bolts. At installation were in the use приводного a disk track correctness of combination of the landing labels put in the course of dismantle.
- Block приводной a disk a method used at removal. In a diagonal order in stages in regular intervals tighten all bolts with demanded effort.
- Establish coupling (Coupling and power shafts see the Head). Remove blocking приводной a disk the adaptation and establish transmission (the Manual 5-step box of a gear change or Automatic 4-step transmission see the Head).
|
|
|
|