Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation

Removal and pallet installation картера

Removal

PERFORMANCE ORDER

Disconnect a negative wire from the battery. Cock a lay brake, then поддомкратьте redock of the car and establish it on props. At a corresponding complete set remove protection картера. Merge impellent oil (see the Head of Adjustment and car routine maintenance), then, having replaced a sealing washer, screw a stopper into place and tighten it with demanded effort. Remove a reception pipe of system of release of the fulfilled gases (see the Head of the Power supply system, release and decrease in toxicity of the fulfilled gases). At a corresponding complete set disconnect from the pallet electroconducting of the gauge of level of oil. On models without К/В turn out bolts of fastening and uncover a flywheel. Removal of a cover of a flywheel On models with К/В turn out bolts of fastening of the pallet картера to картеру transmissions. Bolts of fastening of the pallet картера the engine to a transmission Turn out bolts of fastening of the pallet картера to the block of cylinders. Bolts of fastening of the pallet картера the engine to the block of cylinders Slightly обстучав the pallet from sides a hammer with soft brisk, separate it from картера the engine, lower it and take from under the car. After pallet removal картера it is recommended to disconnect also mesh маслозаборник and to clear it. Bolts of fastening mesh маслозаборника Check up a grid маслозаборника on presence of damages, if necessary replace. Check up passableness of the mesh filter маслозаборника, - wash out a grid solvent, or replace the filter.

Installation

PERFORMANCE ORDER

Carefully smooth out and dry wipe interfaced surfaces of a flange of the pallet and картеров the power unit. Remove all traces of oil, a dirt and old hermetic from a carving of bolts of fastening of the pallet and маслозаборника. In case of need replace a sealing ring and establish into place маслозаборник. Put fixing анаэробный hermetic, for example, OPEL 15 10 177 on a carving part of fixing bolts, screw them and tighten with effort of 8 Nanometers. Installation of a new sealing ring маслозаборника On the engine of 1.6 l and the engine of 1.4 l with К/В tighten bolts of fastening of the pallet картера to картеру transmissions with effort of 60 Nanometers. Put a hermetic layer, for example, OPEL 15 03 294 (90 001 851) on an interfaced surface of the block of cylinders around installation of the oil pump and a cover of the back radical bearing. Places of drawing of hermetic on interfaced to the pallet картера a surface of the block of cylinders Lay on the pallet a new lining, then press the pallet to the block. Grease анаэробным with fixing hermetic, for example, OPEL 15 10 177 carving part of bolts of fastening of the pallet. Screw bolts and, moving from the centre to edges, in a diagonal order tighten them with demanded effort. The further installation is made in a lock, the return to an order of dismantle of components. Fill in in the engine fresh oil (see the Head of Adjustment and car routine maintenance). Make a test trip and check up the pallet картера and a drain stopper on leaks, if necessary slightly tighten bolts of fastening of the pallet картера. If removed, establish into place маслозаборник. Carefully smooth out and dry wipe interfaced surfaces of a flange of the pallet and картеров the power unit. Remove all traces of oil, a dirt and old hermetic from a carving of bolts of fastening of the pallet and маслозаборника. Put a layer of suitable hermetic on an interfaced surface of the block of cylinders around installation of the oil pump and a cover of the back radical bearing. Lay on the pallet a new lining, then press the pallet to the block. Grease анаэробным with fixing hermetic a carving part of bolts of fastening of the pallet. Screw bolts and, moving from the centre to edges, in a diagonal order tighten them with demanded effort. Screw and tighten with demanded effort bolts of a flange of fastening of the pallet. Establish in flange cuts rubber stoppers. Establish a reception pipe of system of release of the fulfilled gases (see the Head of the Power supply system, release and decrease in toxicity of the fulfilled gases). At a corresponding complete set connect electroconducting to the gauge of level of oil sideways on the pallet. At a corresponding complete set establish into place protection картера, then lower the car. Fill in in the engine fresh oil (see the Head of Adjustment and car routine maintenance).