Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation


Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
- Engines
   The general information
   Check компрессионного pressure in cylinders and parametres of impellent oil
   Diagnostics of a condition of the engine with vacuum gauge application
   - Procedures of repair of petrol engines SOHC without their extraction from the car
      Removal and cover installation газораспределительного the mechanism
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of a cover of drive ГРМ
      Removal and installation of a belt of drive ГРМ
      Removal and installation of cogwheels of drive ГРМ
      Replacement of an epiploon of a camshaft
      Removal, check of a condition and installation of a camshaft from the case газораспределительного the mechanism
      Removal, check of a condition and installation of valves
      Removal and installation of a head of cylinders
      Removal and pallet installation картера
      Removal, service and installation of the oil pump
      Removal, check of a condition and installation of a flywheel/privodnogo of a disk
      Replacement of epiploons of a cranked shaft
   + Procedures of repair of petrol engines DOHC without their extraction from the car
   + Procedures of repair of diesel engines without their extraction from the car
   + The general and engine major repairs
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation of a pulley of a cranked shaft

Cнятие

 PERFORMANCE ORDER

  1. Cock a lay brake, поддомкратьте redock of the car and establish it on props. Remove the right forward wheel and (at a corresponding complete set) protection картера.
  2. Remove a belt of a drive of auxiliary units (see the Head of Adjustment and car routine maintenance), - preliminary put on a tape of a belt marks of a direction of its rotation.
  3. Ослабьте a bolt of fastening of a pulley of a cranked shaft, - for the purpose of blocking of a cranked shaft from проворачивания ask the assistant to include the higher transfer and against the stop to squeeze out a brake pedal. On models with АТ give one of bolts of fastening of the hydrotransformer and attach приводной a disk to a dome of transmission by means of a steel lath of pair the suitable bolts equipped with washers. If the engine is removed from the car, block a flywheel/privodnoj a disk (see Has undressed Removal, check of a condition and installation of a flywheel/privodnogo of a disk).
  4. Turn out a fixing bolt (do not forget about a washer) and remove a pulley from a pin of a cranked shaft, - try not to damage the gauge of position of a cranked shaft (CKP).

Installation

 PERFORMANCE ORDER

  1. Accurately plant a pulley on a pin of a cranked shaft, having tracked correctness of landing шпоночного a groove on шпонку. Make sure of completeness of landing of a pulley, - try not to damage gauge CKP. Screw a new bolt with the washer planted on it.
  2. Block a cranked shaft from проворачивания the same method that was used at removal, tighten a new bolt of fastening with effort of 95 Nanometers, then hold on it on a corner 30 hailstones. And on a corner 15 hailstones.
  3. Establish a belt of a drive of auxiliary units (see the Head of Adjustment and car routine maintenance), - track observance of an initial direction of its rotation (see the marks put at removal).
  4. Establish protection картера and a forward wheel.
  5. Lower the car on the earth, then tighten bolts of fastening of a wheel with demanded effort.