Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   The general information and safety measures
   Search of causes of failures of an electric equipment
   Safety locks - the general information
   The relay - the general information and check of serviceability of functioning
   Removal and installation of the e/motor of the uniform lock
   Adjustment of range of light
   Removal and installation of the switch and the e/motor of adjustment of range of light (Model Corsa and Combo)
   Removal and installation of the switch of heating of a seat
   Removal and horn installation
   The antijoy ride device and the alarm system
   Replacement of lamps накаливания in headlights
   Replacements of lamps накаливания devices of external illumination
   Replacement of lamps накаливания in headlights, parking fires and forward indexes of turn of model Tigra
   Replacement of lamps накаливания illumination of salon, a luggage space and a ware box
   Removal and headlight installation
   Adjustment of headlights
   Removal and installation of the back combined lantern
   Removal and installation of an antifog headlight
   Removal and installation of a combination of devices
   Removal and installation of measuring devices and indexes
   Removal and installation of control lamps and the printed-circuit board of a combination of devices
   Replacement of a lamp of illumination of the panel of the block of management with heating
   Removal and installation подрулевого the switch
   Removal and installation of switches of a back foggy headlight (antifog headlight) and heating of seats
   Removal and installation of the switch of external and internal illumination
   Removal and installation of the switch of the alarm system
   Removal and installation of the cylinder of the lock of ignition and its contact element
   Radio receiver installation
   Removal and installation динамиков
   Aerial installation
   Removal and installation of a screen wiper of a windscreen
   Removal and installation of the e/motor of a forward screen wiper
   Removal and installation of the e/motor of a back screen wiper
   Removal and tank and pump installation стеклоомывателя
   Check К/Л of low level of a brake liquid
   Check of serviceability of functioning and regenerative repair of a heater of back glass
   + Schemes of electric connections - the general information


Check of serviceability of functioning and regenerative repair of a heater of back glass

The working element of a heater of back glass represents a horizontal lattice from токопроводных the threads pasted on an internal surface has flown down. A food on a heater moves through the big safety lock from the block of distribution of capacity located in an impellent compartment of the car. Heater inclusion is made by means of the switch located on the panel of devices of the car.

Small breakages токопроводных threads of a lattice of a working element of a heater can be eliminated without dismantle of back glass.

Check

 PERFORMANCE ORDER

  1. Include ignition and a heater of back glass.
  2. Press positive щуп the voltmeter to the positive plug of a lattice of a heating element, negative щуп press to the negative plug. The device should register pressure of the battery, otherwise check up a condition of a safety lock, the switch and connecting electroconducting. If pressure in norm, however, a heater part does not work. Pass to a following stage of check.
  3. To measure pressure during described below checks wind positive щуп the voltmeter with a metal foil which it is easy then a finger will press directly to токопроводной threads of a lattice of a heating element. Negative щуп a measuring instrument connect to the negative plug of a lattice.
  4. Measure pressure in the central part of each of lattice threads. The indication in 5 6 In testifies to serviceability of a condition of a thread. The zero indication speaks about breakage presence between the centre of a thread and an element positive side. Indication overestimate twice (10 12) occurs in the presence of breakage between the centre of a thread and an element negative side. Serially check up each of lattice threads.
  5. In the absence of breakages connect negative щуп to weight of the chassis and repeat check, - indications should not change, infringement of quality of grounding of a lattice otherwise takes place.
  6. For breakage localisation press negative щуп the voltmeter to the negative plug of a lattice of a heating element. Wrapped up by a foil positive щупом start to probe токопроводные lattice threads, moving from outside food givings to weight. In a point of breakage the instrument reading should fall from several volt to zero.

Regenerative repair

 PERFORMANCE ORDER

  1. Integrity restoration токопроводных threads is made by means of special ремнабора type Dupont 4817. The set basis is made токопроводная эпоксидная by the paste delivered complete with a hardener.
  2. Before to start regenerative repair of a lattice of a working element switch off a heater and allow to an element to cool down within several minutes.
  3. Slightly smooth out the damaged site of a thread felt, then carefully wipe its spirit.
  4. Paste two strips of an adhesive tape along a site of a thread subject to restoration.
  5. Carefully get mixed up эпоксидную paste with a hardener (follow instructions applied in a set).
  6. Put the received structure on the damaged site (with a tipping over approximately in 20 mm on edges of the intact thread).

Restoration of the damaged site токопроводной threads of a lattice of a heating element of back glass by means of special эпоксидной pastes

  1. Definitive polymerisation компаунда occurs in 24 hours after which protective strips of an adhesive tape are removed from glass могутбыть.