Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   The general information and safety measures
   Search of causes of failures of an electric equipment
   Safety locks - the general information
   The relay - the general information and check of serviceability of functioning
   Removal and installation of the e/motor of the uniform lock
   Adjustment of range of light
   Removal and installation of the switch and the e/motor of adjustment of range of light (Model Corsa and Combo)
   Removal and installation of the switch of heating of a seat
   Removal and horn installation
   The antijoy ride device and the alarm system
   Replacement of lamps накаливания in headlights
   Replacements of lamps накаливания devices of external illumination
   Replacement of lamps накаливания in headlights, parking fires and forward indexes of turn of model Tigra
   Replacement of lamps накаливания illumination of salon, a luggage space and a ware box
   Removal and headlight installation
   Adjustment of headlights
   Removal and installation of the back combined lantern
   Removal and installation of an antifog headlight
   Removal and installation of a combination of devices
   Removal and installation of measuring devices and indexes
   Removal and installation of control lamps and the printed-circuit board of a combination of devices
   Replacement of a lamp of illumination of the panel of the block of management with heating
   Removal and installation подрулевого the switch
   Removal and installation of switches of a back foggy headlight (antifog headlight) and heating of seats
   Removal and installation of the switch of external and internal illumination
   Removal and installation of the switch of the alarm system
   Removal and installation of the cylinder of the lock of ignition and its contact element
   Radio receiver installation
   Removal and installation динамиков
   Aerial installation
   Removal and installation of a screen wiper of a windscreen
   Removal and installation of the e/motor of a forward screen wiper
   Removal and installation of the e/motor of a back screen wiper
   Removal and tank and pump installation стеклоомывателя
   Check К/Л of low level of a brake liquid
   Check of serviceability of functioning and regenerative repair of a heater of back glass
   + Schemes of electric connections - the general information


Removal and installation of measuring devices and indexes

 PERFORMANCE ORDER

  1. Remove a combination of devices.
  2. Take out a pin of the counter of day run.

Pin of the counter of day run

  1. Raise laths (arrow) and uncover.

The index of a stock of fuel and the temperature index

 PERFORMANCE ORDER

  1. Give two nuts of fastening (on models from 02.1994 вып. - 4 nuts).

Nuts of fastening of the index of a stock of fuel

Speedometer

 PERFORMANCE ORDER

  1. Cautiously remove the printed-circuit board.

Printed-circuit board detachment

  1. Turn out 4 screws of fastening and remove a speedometer At alternative execution from 02.1994 вып. Separate a socket of a speedometer by means of flat-nose pliers, and also turn out 2 screws Torx T20.

Screws of fastening of a speedometer

Tachometre

 PERFORMANCE ORDER

  1. Turn out in front three screws of fastening of tachometre Torx T20.

Voltage stabilizer

The voltage stabilizer carries out a problem of maintenance of onboard pressure at level 12 V.Pri damage of the stabilizer among the other are displayed incorrect value of a stock of fuel.


 PERFORMANCE ORDER

  1. Turn out screws of fastening and remove the stabilizer from an underside of a combination of devices, disconnect it from contacts.

Screws of fastening of a voltage stabilizer

  1. Installation is made upside-down.