Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation

Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   The general information and safety measures
   Search of causes of failures of an electric equipment
   Safety locks - the general information
   The relay - the general information and check of serviceability of functioning
   Removal and installation of the e/motor of the uniform lock
   Adjustment of range of light
   Removal and installation of the switch and the e/motor of adjustment of range of light (Model Corsa and Combo)
   Removal and installation of the switch of heating of a seat
   Removal and horn installation
   The antijoy ride device and the alarm system
   Replacement of lamps накаливания in headlights
   Replacements of lamps накаливания devices of external illumination
   Replacement of lamps накаливания in headlights, parking fires and forward indexes of turn of model Tigra
   Replacement of lamps накаливания illumination of salon, a luggage space and a ware box
   Removal and headlight installation
   Adjustment of headlights
   Removal and installation of the back combined lantern
   Removal and installation of an antifog headlight
   Removal and installation of a combination of devices
   Removal and installation of measuring devices and indexes
   Removal and installation of control lamps and the printed-circuit board of a combination of devices
   Replacement of a lamp of illumination of the panel of the block of management with heating
   Removal and installation подрулевого the switch
   Removal and installation of switches of a back foggy headlight (antifog headlight) and heating of seats
   Removal and installation of the switch of external and internal illumination
   Removal and installation of the switch of the alarm system
   Removal and installation of the cylinder of the lock of ignition and its contact element
   Radio receiver installation
   Removal and installation динамиков
   Aerial installation
   Removal and installation of a screen wiper of a windscreen
   Removal and installation of the e/motor of a forward screen wiper
   Removal and installation of the e/motor of a back screen wiper
   Removal and tank and pump installation стеклоомывателя
   Check К/Л of low level of a brake liquid
   Check of serviceability of functioning and regenerative repair of a heater of back glass
   + Schemes of electric connections - the general information

News & Articles about shopping, lake george adirondack shopping News Articles.

Safety locks - the general information

Various combinations of safety locks, breakers of a chain and fusible inserts can be applied to protection of contact chains of an electric equipment of the car.

The most part of safety locks (and the relay) is located on considered models of cars in the assembly block located at the left under the panel of devices. Procedure of removal of the assembly block is described in the Head the Body.

The second assembly block of safety locks/relays is located in an impellent compartment of the car, has a separate design and is equipped by demountable covers

Each separate safety lock is used for protection of any concrete electric contour or at once several contours. The identification card with the scheme of placing of safety locks in the assembly block is usually glued to a cover of the last, from its internal party.

In assembly blocks the safety locks of a compact design equipped with bayonet contacts, and if necessary easily taken by fingers from the nests in the block are used. At refusal any of electric power consumers first of all always it is necessary to check up a condition of a corresponding safety lock. Turn a key in the ignition lock in position II and by means of a lamp-sampler probe open plugs of each of safety locks. If the lamp lights up at connection to each of plugs, hence, a safety lock as it should be. If pressure takes place only from outside food givings, means, the safety lock has fused. We will notice also that usually the safety lock case is made of transparent plastic through which it is easy to define a condition of a working crosspiece.

The fact перегорания a contact crosspiece of a safety lock easily comes to light at visual survey of an element having the translucent case

At replacement of the fused safety lock strictly watch that the prepared replaceable element corresponded on type failed. The safety locks calculated on a various nominal current strength physically can differ nothing from each other, without being thus interchangeable. Each of electric chains has various working parametres and requires various degree of protection, therefore replacement of the safety lock calculated on a certain current strength not corresponding it on parametres is fraught with the most serious consequences (up to fire occurrence). Working parametres of a safety lock (a nominal current strength) are usually designated on its plastic case colour identification (Specifications in the Head the Onboard electric equipment see), besides, is in addition used.

From the interior of a cover of the assembly block the special clip which use allows to facilitate procedure of extraction of a safety lock appreciably can be attached.

The special clip for extraction of safety locks usually fastens to an inside of a cover of the assembly block

If the new safety lock after installation also fails at once, it is not meaningful to make its further replacement, - before it is necessary to reveal and eliminate the reason of occurrence of an overload in a chain. In most cases that appears the short circuit of connecting electroconducting caused by damage of its isolation. Spare safety locks usually are located in free колодках the assembly block.

On all models of cars considered in the Present Management additional protection of an electric equipment a maximum восемью by the main safety locks placed in the separate block equipped with a cover, fixed on a wall of the assembly block placed in an impellent compartment is provided. Выбивание any of the main safety locks leads обесточиванию большей to an electric equipment part. Before to start replacement of the main safety locks without fail disconnect the storage battery. Replaceable main safety locks always can be got in department of deliveries on firm car repair shop Opel.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! Remember that the failed main safety lock should be replaced with the replaceable calculated on the same current strength.