Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation

The salon equipment

Adjustment of seats

Forward seats

Adjustment of position of seats should be made only on motionlessly standing car!

In Section Elements of systems of safety of the car the important information on safety issues and correctness of adjustment of seats, their backs and headrests is stated, - before a start of motion adjust in appropriate way seat position.

For adjustment of position of a seat in a longitudinal direction delay upwards located under a pillow first line скобу a clamp Keeping скобу in the lifted position, shift seat assemblage forward or back in position convenient for you, then release a clamp. For check of reliability of fixing of a seat try to shift it forward and back.

Adjustment of position of a forward seat in a longitudinal direction

Adjustment of an angle of slope of a back of a seat is made by means of the back of the rotary handle located from an internal lateral surface.

Adjustment of an inclination of a back of a forward seat

The handle of adjustment of height of a pillow of a seat is located from an external forward corner of a pillow.

Adjustment of height of position of a pillow of a forward seat

The lever отпускания the back clamp, allowing to make its folding, is located in the top part of an external wall of a back. For back folding delay the lever upwards.

Folding of a back of a forward seat

Headrests

Headrests help to prevent neck and head traumas at car blow behind. That headrests could carry out effectively the protective functions, they should be adjusted in the correct image. Adjust headrests on height so that the top part of a pillow of a headrest was flush with an auricle upper edge. If high passengers do not manage to achieve it, the headrest is necessary for establishing in as much as possible high position. Adjustment of position of a headrest is made by two hands simultaneously, therefore it is not necessary to try to adjust a headrest during car movement. To lift a headrest, incline it forward on purpose отпускания a clamp, then pull it upwards/drown.

Adjustment of position of a headrest on height

Dismantle of a headrest or replacement is made for cleaning as follows: lift a headrest upwards against the stop, then press buttons of clamps and liberate fixing cores from a seat back.

Headrest dismantle

Back seat

Folding of a pillow and backs of a back seat

The back of a back seat has a separate design and consists of two parts which can develop forward, opening direct access to a luggage space and providing possibility of transportation of large-sized lengthy cargoes.

аждая of two sections of a back of a back seat can develop forward irrespective of another. Buttons отпускания clamps of backs are located from lateral aspects of their upper edges.

Adjustment of a corner of backs of a back seat

Expansion of a luggage space of model Corsa can be made in three various ways.

Variants of expansion of a luggage space

For luggage space expansion by the first way remove a back shelf and headrests, incline backs of a back seat on a necessary corner and fix them in the chosen position.

For luggage space expansion by the second way remove a back shelf and headrests and hang up locks of seat belts on backs of a back seat Press the unblocking button, lay a back of a back seat on a pillow of a seat and put a demountable back shelf for forward seats.

Fastening of locks of seat belts on a back of a back seat

For luggage space expansion by the third way remove a back shelf and headrests, move forward forward seats and hang up locks of seat belts on backs of a back seat. Raise a pillow of a back seat for a loop, and establish it in vertical position on a floor. Press the unblocking button, combine a back of a back seat forward and put a demountable back shelf for forward seats.

Folding of a back of a back seat

At installation of a back of a back seat in a starting position liberate from under a back of a tape of seat belts.

Before return of a back to vertical position do not forget to liberate from under it a seat belt tape

For luggage space expansion on model Combo operate similarly to the third way described for model Corsa, taking into account that the back shelf is absent, and for an unblocking of a back of a seat it is necessary to wring out lever clamps.

Folding of a back of a back seat on model Combo

Headrests

The back seat is equipped by three headrests, left and right from which have the standard design similar to a design of headrests of forward seats.

At folding of seats, or for the purpose of expansion of sector of the back review (at an unoccupied central place of a back seat) headrests should be lowered in extreme bottom position, preliminary having released spring clamps of their cores.

Adjustment of position of a headrest of a back seat

Luggage space

Eyes for safety net fastening

On corners of the panel of a floor of a luggage space the metal eyes are provided, allowing to fix the safety network intended for fixing of transported cargo.

The eyes located in corners of the panel of a floor of a luggage space are intended for fastening of a safety net or a protective lattice

By means of the same eyes on models the Van is fixed also a protective lattice.

Protective lattice (model Combo)

The protective lattice can be mounted behind backs of forward seats (all models Combo), or behind a back of a back seat, (model Combo Tour).

Installation of a protecting lattice

For lattice fastening it is necessary to cut out a covering in the designated points and to fix a lattice from above and from below on either side of. After lattice removal close adjusting apertures covers.

Прикуриватель and the socket of onboard power supplies

Прикуриватель

Прикуриватель it is located in forward section of the central console of the car and functions only at two positions of a key in the ignition lock: I or II, i.e. when ignition or a food of auxiliary consumers of the electric power is included. For inclusion прикуривателя drown before click its button. After heat filched the button automatically with click will return to a starting position.

Assemblage site прикуривателя with an ashtray and sockets of onboard power supplies

In order to avoid an exit прикуривателя out of operation, do not hold its button during spiral heating!

The nest under installation прикуривателя simultaneously carries out a role of the socket of an onboard food in which any auxiliary automobile accessories (the compressor, a vacuum cleaner, зарядное the device for a mobile phone, etc. can be included). For the purpose of providing of access to the socket take from a nest прикуриватель. The consumers of the electric power connected thus at the switched off ignition will work from the battery.

Capacity of consumption of devices connected to an onboard food should not exceed 240 Vt!

Ashtrays

Use ashtrays only on the direct appointment! In order to avoid ignition do not put in ashtrays scraps of a paper, a wrapper from sweets and other combustible materials.

The forward ashtray is united in uniform assemblage with прикуривателем. For ashtray opening press an upper edge of its cover to clear an ashtray of stubs, open a cover of an ashtray and, having pulled upwards, take the reception container from the landing nest (address to an illustration).

Ware boxes

The main ware box is located in the right part of the panel of devices of the car and equipped by a folding cover. Box opening at the included ignition leads to automatic activation of its illumination.

The additional ware box is under a seat of the forward passenger and is extended forward for its handles. This ware box is calculated on loading no more than 1 kg.

Internal rear-view mirror

Internally the rear-view mirror is pasted by the basis on an internal surface of a windscreen, from above in its central part. In the bottom part of assemblage of a mirror it is provided рычажок, allowing to make switching of a reflecting surface in the night mode providing protection of an eye of the driver from blinding by their light moving behind in a passing direction of vehicles.

Рычажок transfer of a reflecting surface of a rear-view mirror in a night mode it is located in the bottom part of assemblage

Heating of forward seats

At corresponding the complete set ции switches of heating of forward seats are located in a forward part of the central console under handles of management of a heater and marked by the pictogramme. The left switch operates heating of a seat of the driver, and right - heating of a seat of the forward passenger.

Arrangement of switches of heating of forward seats

Control lamps of inclusion of heating of seats are built in switches.

Switches of management of functioning of the electric drive of external rear-view mirrors

On models with a manual drive of external mirrors adjustment of their position is made by means of the mirrors located from the interior of the bases рычажков.

On the models equipped with the electric drive of adjustment of external rear-view mirrors, the switch of management is located by electric drive functioning from the interior of forward doors of the car in places of their adjunction to the panel of devices.

The block of management of position and heating of an external mirror

The choice of a mirror subject to adjustment is made by moving to the corresponding party top ползункового the switch. Actually updating is carried out by means of the bottom rotational switch. Do not forget to return on termination of adjustment ползунковый the switch in average (neutral) position in order to avoid risk of casual infringement of demanded position of a mirror.

The switch of heating of external rear-view mirrors

The switch of heating of external mirrors is in the block of management of position and heating heating Inclusion is accompanied by operation of the indicator close to the switch.

Heating is disconnected automatically in 15 minutes after its inclusion.