Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   The general information
   + Forward suspension bracket
   - Back suspension bracket
      Removal and installation of a spring of a back suspension bracket (model Corsa and Tigra)
      Removal and installation of the stabilizer of cross-section stability (model Corsa and Tigra)
      Removal and installation of the bearing of a wheel
      Backlash adjustment in the wheel bearing
   + Steering
+ Body
+ Onboard electric equipment


Removal and installation of the bearing of a wheel

The wheel bearing on car Opel Combo is in a separate nave of a wheel whereas on other models it is directly in a brake drum. Besides, bearings of wheels and a brake drum on model Combo have stronger design.

Removal

 PERFORMANCE ORDER

  1. Поддомкратьте a back of the car also establish it on props.
  2. Remove a brake drum (the Brake system see the Head).
  3. On model Combo remove пыльник the bearing by means of a wide screw-driver. Take out шплинт nuts of a pin of a wheel and give a nut. Remove a nave with a press disk from a pin.

Nave removal on model Combo

  1. Take out a screw-driver a sealing ring from a nave, trying not to damage a nave thus.

Removal of a sealing ring

  1. Take out the internal conic roller bearing.
  2. Cautiously beat out by means of brass выколотки an internal holder of the bearing. To exclude перекашивание holders in a nave, establish выколотку alternately in opposite points of a ring.

Extraction of an internal holder of the wheel bearing

  1. Similarly cautiously beat out by means of brass выколотки an external holder of the bearing. HUNDRED Opel apply for this purpose the special tool.

Extraction of an external holder of the wheel bearing

  1. Clear a nave of a wheel the pure rags moistened in spirit.

Installation

 PERFORMANCE ORDER

  1. The bearing replace necessarily in the complete set (internal and external holders and bodies качения) in spite of the fact that worn out can seem only one of holders.
  2. Check up полуось on presence of damages and deterioration, if necessary address on HUNDRED for its replacement.
  3. Establish against the stop bearing holders. If the special tool for this purpose is not present, напрессуйте a ring by means of a piece of a suitable pipe.

Installation of holders of the bearing

  1. Fill the bearing литиевой with greasing and establish it on полуось.
  2. Establish the internal bearing.
  3. Grease a new sealing ring between working edges and запрессуйте it into place by means of a piece of a pipe of the corresponding diameter. On model Combo similarly arrive with a nave.

Installation of a sealing ring

  1. Grease the external conic bearing and insert it into a nave.
  2. Establish on полуось a nave or a brake drum and establish the external bearing. Thus watch that the dirt has not got to the bearing.
  3. On model Combo establish a press washer and screw a nut of a nave of a wheel.

Before installation of a cover of a nave unbend both ends of a lock pin

Order of installation of a cap ступичной nuts on models Combo

  1. Establish a brake drum (Engines see the Head).
  2. Establish a wheel so that the labels put at removal have coincided. Lower the car on the earth and wrap bolts of fastening of wheels cross-wise with effort of 110 Nanometers.
  3. Adjust a backlash in the wheel bearing.