Opel Corsa B, Combo, Tigra

Since 1993-2000 of release

Repair and car operation



Opel Corsa B, Combo, Tigra
+ Cars Opel Corsa B, Tigra and Combo
+ Controls and operation receptions
+ Options and car routine maintenance
+ Engines
+ Systems of cooling of the engine, salon and air conditioning heating
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual 5-step box of a gear change
+ Automatic 4-step transmission
- Coupling and power shafts
   The general information
   - Coupling
      Removal and coupling installation
      Removal, check and installation of the bearing of deenergizing of coupling
      Replacement of a cable of a drive of coupling
      Check of a condition of components of coupling
   + Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Check of a condition of components of coupling

Remember that developed in the course of deterioration of frictional overlays of a conducted disk of coupling the dust can contain unhealthy asbestos. Do not blow off a dust the compressed air and try not to inhale it. Do not apply to rubbing of components of coupling solvents on an oil basis, - use only special brake cleaners or pure methyl spirit. The used rags put in tightly closed container.


 PERFORMANCE ORDER

  1. More often infringement of serviceability of functioning of coupling appears connected with deterioration of frictional overlays of a conducted disk. Nevertheless, it is necessary to study attentively a condition of all other components of assemblage.
  2. Study a working surface of a flywheel on presence of cracks, traces of an overheat, furrows and other damages. Insignificant defects can be eliminated a way проточки in the conditions of a car-care centre workshop (проточку it is recommended to make without dependence from a surface condition). The description of procedures of removal and flywheel installation is resulted Section Removal, check of a condition and installation of a flywheel/privodnogo of a disk. Also check up a condition and estimate planeness of an interfaced surface of a press disk of coupling.

Measurement of planeness of an interfaced surface of a press disk of coupling

  1. Estimate degree of deterioration of frictional overlays of a conducted disk of coupling. The surface of overlays should tower over heads of rivets at least on 1.6 mm. Make sure of density of landing of all rivets, check up торсионные springs/dempfery on presence of cracks, traces of deformation and other mechanical damages of Zamaslivanie of frictional overlays is the result of failure of an epiploon of a cranked shaft, infringement of integrity of a lining of the pallet картера more often, a sealing element of assemblage of the executive cylinder or an epiploon of primary shaft РКПП, - replace the damaged components. As already it was mentioned above, replacement of components of coupling it is reasonable to make each time at assemblage dismantle, therefore pay attention to the slightest errors.

Assemblage of a conducted disk
1 — Frictional overlays - in a picture are worn out below an admissible limit
2 — Torsionnye of a spring or демпферы - should be checked up on presence of cracks and deformation signs
3 — Equipped шлицами the nave - should slide freely on шлицам a primary shaft of a transmission, шлицы should not be worn excessively out
4 — Rivets - are used for fastening of frictional overlays and at excessive deterioration of the last start to leave furrows on a working surface of a flywheel

  1. Together with a conducted disk always it is replaced as well выжимной the bearing. If the conducted disk is perfectly in order, check up a condition выжимного the bearing, - the bearing should rotate smoothly, without jamming signs. Interfaced surfaces should be absolutely smooth and not damaged, without cracks, задиров and hollows. In the absence of confidence of definition of a condition of the bearing make replacement of assemblage of the executive cylinder (see Has undressed Removal, check and installation of the bearing of deenergizing of coupling).
  2. Estimate a condition of the processed surfaces and petals диафрагменной springs of a press disk In case of revealing of defects replace basket assemblage. Traces of easy polishing can be removed by means of a fine-grained emery paper. Through firm car repair shops of company Opel always it is possible to get the restored assemblage of coupling on an exchange basis.

Deterioration examples диафрагменной springs

Normal deterioration of petals.
Excessive deterioration of petals.
Petals are broken off or погнуты.